Відео

Sweet ride....

Have one in my 1963 c 10 it's junk only 16,000 miles and it's falling apart. Going to have to replace it .

My problem is i can stand on ebrake and it wont hold with good engagement. Brakes work but dont have ebrake holding power.

Do you make a kit for 93 Fleetwood?

Too bad you did not discuss installing this box on a 4 speed car, and show the part of the box that needs to be cut off to allow clearance for the the Z bar, this is a very important part of the install and is not clearly discussed in the instructions. Only part of the kit I was disappointed with as it caused me a LOT of grief!! Maybe its my fault, but I firmly believe it should be a major focus of the video, save a lot of people the grief I went through!!

I've installed TMI interior in two chevy trucks now. Dash pad is a horrible fit around the gage panel, it doesn't have clips to hold the front edge in position, the door panels don't have hardly any fasteners, and the biggest complaint is the driver seat adjustment handle is on the left front of the seat. If you are trying to work on the wiring under the dash, the handle is constantly stuck in your back. The fabric around the ac ducts was just bent around a fiberglass backing and glued, but came loose and had edges hanging out. Yes it looks cool all installed, but it is doesn't fit well, and very low quality, and workmanship. I feel my customers could have spent the 5 grand for a seat, dash pad and door panels on better quality components.

You said you sell the spacer and horh circle thing separate. I have the exact setup as you show in the video but no spacer etc. How do I get it?

OH BROTHER! Can you in any way donate everything that you took out of your truck, to an old disabled man who's trying his best to fix up his old 79 C30 crewcab dually? The truck is white, so a black & white interior would be awesome for it! 😮😊🙏🙏🙏🙏🙏🙏!

72 impala which one do I need 5.3 swap

I need a system for a 1976 BJ40 steering and brakes conversion.

When will the frame with the triangulated 4-link be available?

Cool looking truck

Working on adding a return line to factory tank. Would I have to drop the tank to add this?

Working on adding a return line to factory tank. Would I have to drop the tank to add this?

excellent video

Give me a phone number where I can call you

Will this fit on my 1969 Buick wildcat 4 dr?

Nice try

With this kit fit gbody rear ends

Will this fit a 2006 tahoe with hydrboost?

Thank for the lesson.

69 ford e100 van 🤔???

Well DoNe ViKiNg CCP for the ChoiCe of RiDe.

Would you sell the old interior ?

Don't buy cpp hubs , super low quality and dangerous .

❤

Is there a kit for a 65 f250..?

The interior looks really nice now it looked nice before I have looked at TMI interiors I can't afford 5 or 6,000 for an interior panels

For adjusting the hand brake like you did in the video, my hand brake rear left wheel is loose, the one on the right is good, i lift the rear car both wheels in the air and applied the hand brake and rear right wheel is really strong checked by hand if i can move it , but on rear left i can move it by hand, so i think this is what i have to do, to adjust like you did, is that means because hand brake is loose for that wheel is normal foot brake loose as well for that wheel? And does need brake bleeding after this or just adjust and good to go?? Thanks. Nice video

Trash trash trash I bought that kit 5 years ago fuel line crack on me leaked fuel everywhere

Is this callibration for hand brake or for normal foot brake?

Do your cast iron exhaust manifolds work on a first gen camaro with power steering?

You mentioned an air breather. Why do you need an air breather, the second install you do not mentioned or install an air breather. Do you need one?

I need a rear for a 72 nova? You guys make?

I bought one of these from you guys, but I did not get a video on how to put it into my El Camino that I bought it for a 1983 El Camino and I can’t find videos on how to install it

I'm trying to order your master cylinder bleed kit, but it won't download.

Cut the video so they didn’t have to show holes being drilled for improper placement of screws on the TMI dash cover lol

How does this compare to a CJ brake booster

Hey Jason, good to meet ya buddy. I enjoyed the video and it was pretty straight forward. I do want to ask though if I could get your advice on something. I have a 2005 Cadillac SRX 4.6L and the E-Brake not working almost got us killed about a month ago out on 23S in Kentucky. The mountains aren't anything to mess with and the brakes are literally life or death here, more so than in the city (Columbus, Ohio) where I am from. So I have the parking brake not engaging at all in Drive and this was an issue where the passenger's side brake line failed toward the back and we had to swing in a parking lot full of people going out 45mph, circling the lot and honking our horn until it began to get attention. *******I have been trying to figure this out and have literally no one to help me. Yesterday I started it up, held the brake in and shifted to drive and pressed in the E Brake and let up off the regular brake - the car rolled with no grab from the E Brake, but it held (although lightly) in reverse. Anything you can tell me to help me would be greatly appreciated. The Front Passenger's side also has a rupture in the brake line right behind the wheel on the inside of the engine cabin that I can't seem to get to with a cutter to put in a section of brake line and the caliper on that wheel is also not engaging at all. Anyone you know in the area that could help and any advice you can offer would be great, buddy. What you think? Have a great day, brother!

can i have the interior you guys took out for my truck lol just in case if its in the shop laying around

Now let’s talk about the bleeding procedure. Do you bleed them with the calipers parking brake engaged or disengaged? Also…….. One of my calipers. Drivers side only. Is pulling in air. It is not leaking fluid but it is sucking in air for sure. I know this because I have a sealed brake bleeder that’s open. No air is coming into the threads. It’s hooked up to a long 3/16 line that’s attached to the bleeder. It runs……back to the master cylinder. I have both rear calipers set up this way. The drivers side keeps pulling in air and the passenger side doesn’t. Neither leak fluid. As for the parking brake. As long as you do it empty and off the car. It’s easy to get that 1/16th engagement. I found the parking brake easy to get right. But I can’t get it to bleed the air out. That one side makes for a very soft pedal

Thank you.

That was awesome

I was trying to find the stainless ones on your website, but your website sucks. Looks like it was made in 1995, hard to navigate and find stuff. Not to mention the manifolds I was interested in isn't even listed in the Buy it now, but shows up in the picture... 🤔🤷‍♂ Guess I'll just get some off Summit...

It looks like you're working on a '55-'59 Chevy truck. I'm installing a remote system from Johnny Law Motors. It only uses one hose and the fitting they give for the master cylinder lid had bolt threads. I had to use a pipe thread tap and a pipe fitting to prevent a leak. The master cylinder lid finish was so rough, I had to sand it. I'm going to glue the gasket on with contact cement because the lid is flat. It comes with a brass plug for the "extra" hole in the bottom of the new reservoir that I had to add a small o-ring to inside. Last thing, There is no air bleed hole in the new reservoir. What the hell? That should work just fine. NOT! I'm drilling a .020 hole in the side of the cap.

Whats the part number for this kit 55 to 57 tri 5 i want to run my 14 inch wheels

Any idea if or how long it might be before LT manifolds become available?

Why post something you do not actually sell?

Safe for plastic tanks???

Where did you get your steering wheel from